BA-8103-1 Brackett Air Filter Element

Manufacturer: Brackett

Part Number: BA-8103-1

$18.37

BELLANCA 14-19-3A, 17-30 CESSNA 180A Thru K CESSNA 182 Thru R CESSNA 185 Thru E, A185E, F REIMS (CESSNA) F182P, F182Q CHAMPION 7GCAA, 7GCBC, 8GCBC, 7KCAB, 8KCAB

Condition *

Availability: Out of stock

Qty:

+ -

Alternate Products:

Price Valid Until Stock is Depleted

Overview

"Dust or some form of dirt is frequently the principle factory in premature piston ring and cylinder wear. If a worn or poorly fit air filter allows as much as a tablespoon of abrasiver dirt material into the cylinders, it will cause wear to the extend that an overhaul will be required." -Lycoming Engines

Why Choose Anything Less Than A Brackett Filter?

Reasons to Choose a Brackett Air Filter:

Brackett is FAA-PMA approved on 88 different aircraft models.
Brackett's patented treated foam has a 98% efficiency rating.
You replace only the low cost, throw-a-way, element.
Easy, accurate servicing by replacement at specified times.
Dual stage foam element increases dust holding capacity.
It's a proven filter. Brackett Air Filters (formerly AC) have been in service on aircraft and helicopters since 1968. At present, Brackett Foam Filters are installed as Factory original equipment on many production aircraft and helicopters.
Brackett's foam filter is unaffected by water (approved for sea planes). It has no pleats to store dirt and is abrasive resistant.
All Brackett filters exceed MIL-SPEC-7194A

Brackett gives you more filter...and more value!

Installation Tips

In cases where the filter frame is to be attached, occasionally a broken or bent airloc fastener is found. Restoring the ability to secure the filter is of prime importance; any good method of bolting or screwing the frame on is acceptable.
Check to make sure that the gasket makes good contact around the periphery and it’s compressed to approximately 1/2 the original thickness.
If the element wettant congregates to one end, blot the excess with clean dry cloth. If your installation tools become sticky, use WD-40 to clean up.
Check and be sure the rest of the air intake is in good shape and look for torn rubber couplings, worn carburetor heat valve, or alternate air doors. With these in good condition, you can feel confident your engine is operating in a clean air environment.
For continued inservice instructions, reference Form I-194 located on the back side of the Filter Element Bag.
Check the date of manufacture. Elements are only good for 4 years from date of manufacture listed on the element packaging.

Customers who bought this item also bought

W100 Aeroshell AEROSHELL AVIATION OIL W100 SAE 50

Part Number: W100

1014 in stock - New

Aeroshell W100 is an ashless, SAE 50 dispersant oil that provides excellent service in all four cycle aircraft piston engines. We understand your desire for low-cost, dependable flight. You can rely on AeroShell products to help protect your engine, reduce its maintenance costs and improve its efficiency. Whether you fly for pleasure or your business depends on flight, AeroShell products are designed to help lift your performance. Single Grade Ashless Dispersant Oils AeroShell Oils W80, W100 and W120 are ashless dispersant oils specifically developed for aviation piston engines. They combine non-metallic additives with selected high viscosity index base oils to give exceptional stability, dispersancy and anti-foaming performance. No general rule exists for every engine type when choosing the correct grade of oil; however, based on the average ambient outside temperature at engine start-up the most common grades are SAE 40, SAE 50 and SAE 60, which equates to AeroShell Oil W80, W100 and W120 respectively. Traditionally, the choice is associated with climatic zones - AeroShell W80 for cold climate regions (-17 - 21°C), AeroShell Oil W100 for temperate regions (15 - 30°C) and AeroShell Oil W120 for warmer climates (above 26°C). AeroShell Oils W80, W100 and W120 are produced to meet fully the SAE specification J-1899 (Grades SAE 30, 40, 50 and 60 respectively). Furthermore, they all have military qualification approval and are listed on the Qualified Products List (QPL) issued by the US Navy and on the Technically Acceptable Products List (TAPL) issued by the UK Ministry of Defence. The blending plants employed to manufacture these oils also hold the approval of the specification authorities and this ensures that the high quality standard is always maintained.

$9.82